admin管理员组文章数量:1534393
2024年1月16日发(作者:)
计算机错误提示大全及详解计算机错误提示大全及详解2010年04月04日星期日13:59计算机错误提示大全及详解
1、BIOS中的提示信息Drive Aerror驱动器A错误System halt系统挂起Keyboard controller error键盘控制器错误Keyboard error or no keyboard
present键盘错误或者键盘不存在BIOS ROM checksum error BIOS ROM校验错误Single hardisk cable fail当硬盘使用CABLE选项时硬盘安装位置不正确FDD Controller Failure BIOS软盘控制器错误HDD Controller Failure BIOS硬盘控制器错误Drive Error驱动器错误Cache Memory Bad,Do not Enable
Cache高速缓存CACHE损坏,不能使用Error:Unable to control A20 line错误提示:不能使用A20地址控制线Memory write/Read failure内存读写失败Memory allocation error内存定位错误Cmos Battery start LOW CMOS没电了Keyboard interface error键盘接口错误Hard disk diver failure加载硬盘失败Hard disk not present硬盘不存在Floppy disk(S)fail(40)软盘驱动器加载失败,一般是数据线插反,电源线没有插接,CMOS内部软驱设置错误CMOS checksum error-dfaults loaded CMOS校验错误,装入缺省设置2 BIOS刷新失败后,BOOTBLOCK启动时出现的提示信息Detecting floppy drive
Amedia…检测软驱A的格式Drive media is:1.44Mb1.2Mb 720Kb 360Kb驱动器格式是1.44Mb1.2Mb 720Kb 360Kb Disk Boot FAILURE,INSERT SYSTEM磁盘引导失败,插入系统盘后按任意键继续DISK AND PRESS ENTER 3MBR主引导区提示信息Invalid partition table无效的分区表Error loading operating
system不能装入引导系统Missing operating system系统引导文件丢失4、DOS活动分区中的提示信息Invalid system disk无效的系统盘Disk I/O
error,Replace the disk and press any key.磁盘I/O错误,替换磁盘后按任意键(当C盘系统文件丢失或被破坏时出现该提示信息。可用SYS C:修复系统文件)Invalid Media Type reaching Drive C:无效的C盘媒体格式说明。也就是C盘没有格式化或者是其他操作系统的磁盘格式如NTFS Invalid Boot
Diskette Boot Failure无效的启动盘,启动失败5 中的提示信息Insert diskette for drive and press any when ready插入磁盘到驱动器中
后按任意键Your program caused adivide overflow error If the problem
persiste,contact your program vendor你的程序导致溢出错误如果该问题还存在,请联系你的程序供应商Windows has disabled direct disk access to
protect your long filenames WINDOSWS不能直接访问受保护的长文件名The
system has been Ctrl+Alt+Del to restart your computer系统挂起,按Ctrl+Alt+Del重新启动你的计算机You started your computer
with aversion of MS-DOS incompatible with this version of
aStartup diskette matching this version of Windows and
then restart你启动的MS-DOS版本与Windows版本不兼容,请插入与Windows版本匹配的系统盘后再重启(意思是: 与不匹配)This version of Windows requires a386 or better processor该Windows版本需要386以后的CPU支持A20 hardware t
technical support to identify the problem地址线A20错误。联系技术支持来识别该问题starting Windows 98…正在启动Windows 98…Windows 98 is
now starting your MS-DOS-based program Windows 98正在启动基于MS-DOS的程序Windows 98 is now restarting…正在重新启动Press ESC now to
cancel MS-DOS mode and restant windows 98…按ESC退出MS-DOS模式,重新启动windows 98…There is an unrecognized command in your
file在你的文件中有不可识别的命令The following
command in your file is incorrect在你的有下列错误命令The sector size specified in this file is too large:该文件中指定的扇区太大The following file is missing or corrupted:
下列文件丢失或被破坏: There is an
invalid country code or code page in your file在你的里有一个无效的国家代码There is an error in the COUNTRY
command in your file在你的里有一个错误的设置国家命令There is not enough memory for the file没有足够的内存来加载文件Remove some drivers from your
file,and then try again请从文件中删除部分驱动程序,然后再试(这个信息常见于DOS程序运行时内存空间不足时系统提示)Remove some
drivers,and then try again去除一些驱动程序,然后再试。这里的驱动程序是指在中使device或devicehigh命令加载的程序文件Remove
some disk drivers from your file,and then try again从你的移去部分程序,然后再试The configuration specified in your
file is too large for memory调整你的文件以获得足够大的内存You have too many block devices specified in your
file调整你的文件以获得block devices The STACKS
setting(S)in your file are incorrect在你的中堆栈设置不正确Default stack settings will be used instead缺省的堆栈设置将被替代使用There is an error in your file on line XX在你的里XX行错误Warning:Logical drives past Zexist and
will be ignored警告:逻辑驱动器Z已经存?br冢缓雎?BR Type the name of
the Command ,C:)press any key to
continue…请输入命令解释器的文件名(如:C:)后,按任意键继续Windows is bypassing your startup files Minimal network
support will be loaded if available Windows正在跳过你的启动文件如果网络可用,最小网络支持将被加载Windows is starting the command prompt
only Windows正在启动命令字符模式Windows will prompt you to confirm
each startup command Windows将提示你确认每一个启动命令The
compression driver cannot be set up correctly压缩驱动器不能被正确加载Get aversion from your vendor that is compatible with this version
of windows从你的供应商那里获得一个与WINDOWS版本相兼容的版本Process
the system registry运行系统注册表Create astartup log
file()创建启动日志文件process your startup
device drivers()运行文件中的设备驱动Process
your startup command file()运行中的启动命令Load the widows graphical user interface装入WINDOWS图形用户界面(GDI)Warning:windows has detected aregistry/configuration
,Command prompt only,and run SCANREG警告:windows检测到一个注册表或配置错误选择DOS操作模式,运行SCANREG Warning:WINDOWS
has detected acompressed drive access saft mode command
prompt only,to help you identify the problem警告:windows检测到一个访问压缩驱动器错误,选择安全模式下的MS-DOS,来帮助你识别这个问题Warning:windows did not finish loading on the precious
safe mode,to start windows with aminimal set of
drivers警告:windows在刚才尝试后不能够完成加载,选择安全模式,用最小驱动启动你的电脑Warning:WINDOWS multi-boot may not function
correcrly Check for system files in your root directoty with
conflicting extensions警告:WINDOWS不能够正确完成多系统启动,在你的ROOT目录里检查不一致的系统文件Warning:the system configuration
manager failed to of your real-mode device drivers may not
initialize properly警告:系统管理器运行失败,一些实模式驱动可能没有正确初始化The BUFFERS setting(S)in your file are too
t buffer setting will be used instead在你的里BUFFER设置太大。默认的BUFFER缓冲器设置将被使用A memory allocation
error occurred during startup restart your computer and select
interactive start to identify the problem在启动过程中内存分配发生错误,请重新启动你的计算机然后选用交互方式启动来确定故障原因Warning:the high memory area(HMA)is not available Additional low memory(below
640K)will be used instead警告:高端内存不可用,低端内存将被代替使用There is not enough memory for some drivers from your
file,and then try again对Windows来说没有足够的内存,请从文件中移去部分加载的程序,然后再试着启动你的读入计算机Your
previous MS-DOS file were not found.旧的MS-DOS文件没有找到,这常见于使用双启动的系统,另一个系统是DOS6 Your previous MS-DOS version is
not -DOS startup failed旧的MS-DOS版本不支持MS-DOS启动失败Now loading your previous version of MS-DOS,please wait现在正在加载旧的MS-DOS版本,请等待Invalid setting in the file:AN
internal stack overflow has caused this session to be halted
文件中无效的设置选项系统堆栈溢出,系统挂起Change the STACKS
setting in your file,and then try again请改变文件中的STACKS设置,然后再试Stack overflow堆栈溢出Integer divide
by 0整数被0除Not enou gh space for environment没有足够的空间Run-time error运行错误Floating-point support not loaded浮点运算支持没有装入Null pointer assignment无效的断点分配6 COMMAND中的提示信息stack overflow堆栈溢出integer divide by 0分母是0 not enough space
for environment磁盘没有足够的空间run-time error时钟错误no fixed
disks present没有硬盘存在insufficient memory内存不足invalid drive
specification无效的驱动器名invalid characters in volume label无效的盘符invalid volume ID无效的卷标ID号no target drive specified目标驱动器没有定义missing operating system系统文件丢失non system Disk or
Disk Error不是系统盘或磁盘错误Replace Disk and Press Anykey To
Reboot替换磁盘,按任意键重新启动7 SYS传送系统文件时的提示信息cannot
find system files不能找到系统文件system transferred系统传送完毕disk
unsuitable for system disk目标磁盘不适合做系统盘8 FORMAT中的提示信息unable to write BOOT不能写引导扇区invalid media type无效的磁盘类型parameters not supported参数不支持cannot format anetwork drive不能格式化网络驱动器invalid media or track 0bad-disk unusable无效的磁盘或0磁道损坏,磁盘不可用format terminated格式化终止disk boot
failure磁盘BOOT区错误invalid system disk无效的系统磁盘disk I/O
error,replace the disk,and then press any key磁盘I/O错误,请换盘后按任意键。通常在读写软盘时出现次类错误non-system disk or disk
error,replace and strike any key when ready无系统的磁盘或磁盘错误,请替换后按任意键too many open files打开的文件太多access denied
insufficient memory没有足够的内存访问被拒绝invalid drive
specification无效的磁盘说明parse error XX分析错误XX incorrect MS-DOS version不正确MS-DOS版本X%percent completed格式化正在进行,已经完成X%Format complete.格式化完成XX bytes in bad sectors XX字节的坏扇区XX bytes total disk space磁盘的全部空间为XX字节XX bytes
available on disk磁盘的可用空间为XX字节volume label(11
characters,ENTER for none)?请输入磁盘卷标(总共11个字符,按回车为空)format not supported on drive Xformat命令不支持驱动器X invalid
device parameters from device driver无效的设备驱动参数Error writing
FAT写FAT表错误error writing directory写DIR目录表错误cannot format
an ASSIGN or SUBST drive不能格式化ASSIGN和SUBST指定的驱动器cannot
find system files没有找到系统文件cannot format anetwork drive不能格式化网络驱动器invalid characters in volume label磁盘卷标中存在非法字符Parameters not supported参数不支持Format terminated格式化意外终止
Disk unsuitable for system disk这个磁盘不适合作为系统盘unable to
write boot不能写BOOT区Error reading directory读DIR目录区错误no
target drive specified目的驱动器没有说明and press ENTER when ready准备好后按回车System transferred系统传送完毕Enter current volume
label for drive X请为驱动器X输入磁盘的卷标Parameters not compatible
with fixed disk参数与硬盘不兼容Volume serial number is XXXX分区格式化时随机产生的序列号是:XXXX Format broken格式化被强行终止Format not
available on drive XX不能在驱动器XX上使用格式化命令on-system disk
or disk error没有系统盘或磁盘错误Bad partition table错误的硬盘分区表parameters not supported by drive该驱动器不支持这些参数insert DOS
disk in dri ve A请在驱动器A中插入DOS系统盘WARNING,ALL DATA ON NON-REMOVABLE DISK DRIVE%1:WILL BELOST!Proceed with警告:硬盘分区X中的所有数据都将丢失,确定执行格式化命令吗?Format another(Y/N)?!还格式化其他硬盘吗error reading partition table读硬盘分区表错误error
writing partition table写硬盘分区表错误parameters not compatible参数不匹配XX allocation units available on disk磁盘上有XX可用簇XX
bytes in each allocation unit每个簇有大小为XX字节Same parameter
entered twice相同的参数被输入两次Must enter both/T and/N
parameters/T和/N参数必须同时使用There is not enough room to create
arestore file没有足够的空间来建立恢复文件YOU will not be able to use
the UNFORMAT utility你将不能使用UNFORMAT工具来恢复你的硬盘数据There
is not enough disk space for system files没有足够的空间来存储系统文件This disk cannot be unformatted这个磁盘不能被反格式化There was an
error creating the format recovery file在建立恢复文件时产生一个错误Volume label is not supported with/8 parameter该驱动器不支持/8参数Insufficient memory to load system files没有足够的内存装入系统文件Insufficient memory内存不足calculating free space(this may take
several minutes)…正在统计磁盘空间(可能要花几分钟)
版权声明:本文标题:计算机错误提示大全及详解 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://m.elefans.com/dianzi/1705358133a135011.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论