admin管理员组文章数量:1638752
2024年5月8日发(作者:)
1. 计算机命令:
PCA login: root ;使用root用户
password: linux ;口令是linux
# shutdown -h now ;同init 0 关机
# logout
# login
# ifconfig ;显示IP地址
# ifconfig eth0
# ifconfig eht0
# route add 0.0.0.0 gw
# route del 0.0.0.0 gw
# route add default gw
# route del default gw
# route
# ping
# telnet
2. 交换机支持的命令:
交换机基本状态:
switch:
rommon>
态
hostname>
hostname#
hostname(config)#
hostname(config-if)#
交换机口令设置:
switch>enable
switch#config terminal
switch(config)#hostname
switch(config)#enable secret xxx
switch(config)#enable password xxa
switch(config)#line console 0
switch(config-line)#line vty 0 4
switch(config-line)#login
switch(config-line)#password xx
switch#exit
交换机VLAN设置:
switch#vlan database
switch(vlan)#vlan 2
switch(vlan)#no vlan 2
switch(config)#int f0/1
;设置网关
;删除网关
;显示网关
;交换机的ROM状态
;路由器的ROM状
;用户模式
;特权模式
;全局配置模式
;接口状态
;进入特权模式
;进入全局配置模式
;设置交换机的主机名
;设置特权加密口令
;设置特权非密口令
;进入虚拟终端
;允许登录
;设置登录口令xx
;返回命令
;进入VLAN设置
;建VLAN 2
;删vlan 2
;进入端口1
;进入控制台口
switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2
switch(config-if)#switchport mode trunk ;设置为干线
switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan
switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继
switch(config)#vtp domain
switch(config)#vtp password
switch(config)#vtp mode server ;设置发vtp模式
switch(config)#vtp mode client ;设置发vtp模式
交换机设置IP地址:
switch(config)#interface vlan 1
switch(config-if)#ip address
switch(config)#ip default-gateway
switch#dir flash:
交换机显示命令:
switch#write
switch#show vtp
switch#show run
switch#show vlan
switch#show interface
switch#show int f0/0
3. 路由器支持的命令:
路由器显示命令:
router#show run
router#show interface
router#show ip route
router#show cdp nei
router#reload
路由器口令设置:
router>enable
router#config terminal
router(config)#hostname
router(config)#enable secret xxx
router(config)#enable password xxb
router(config)#line console 0
router(config-line)#line vty 0 4
router(config-line)#login
router(config-line)#password xx
router(config)#(Ctrl+z)
router#exit
;进入vlan 1
;设置IP地址
;设置默认网关
;查看闪存
;保存配置信息
;查看vtp配置信息
;查看当前配置信息
;查看vlan配置信息
;查看端口信息
;查看指定端口信息
;显示配置信息
;显示接口信息
;显示路由信息
;显示邻居信息
;重新起动
;进入特权模式
;进入全局配置模式
;设置交换机的主机名
;设置特权加密口令
;设置特权非密口令
;进入虚拟终端
;要求口令验证
;设置登录口令xx
; 返回特权模式
;返回命令
;进入控制台口
版权声明:本文标题:思科模拟器命令 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://m.elefans.com/dianzi/1715155620a438005.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论