admin管理员组文章数量:1534188
2024年6月3日发(作者:)
用uefi方式引导安装windows 10的方法
Installing Windows 10 using UEFI Boot Mode
To install Windows 10 in UEFI mode, you'll need to follow
these steps:
1. First, make sure that your computer supports UEFI boot
mode. Most modern computers manufactured after 2011 should
have this capability.
(第一步,确认计算机支持UEFI引导模式。大多数在2011年后生
产的现代计算机都应具备此功能。)
2. Next, access the BIOS (Basic Input/Output System)
settings by restarting your computer and repeatedly
pressing a specific key or combination of keys during the
startup process. The specific key(s) to enter the BIOS
varies depending on your computer's manufacturer, but
common keys include F2, Del, Esc, or F10.
(接下来,通过重新启动计算机并在启动过程中反复按下特定的键
或键组合来访问BIOS(基本输入/输出系统)设置。要进入BIOS的
特定键取决于计算机的制造商,但常见的键包括F2、Del、Esc或
F10。)
3. Once in the BIOS settings, navigate to the "Boot" tab or
section and locate the "Boot Mode" or "UEFI Boot" option.
Enable UEFI Boot if it is not already enabled.
(进入BIOS设置后,导航到“启动”选项卡或部分,并找到“启动
模式”或“UEFI引导”选项。如果尚未启用,启用UEFI引导。)
4. Save your changes and exit the BIOS settings.
(保存更改并退出BIOS设置。)
5. Insert the Windows 10 installation media (DVD or USB)
into your computer.
(将Windows 10安装介质(DVD或USB)插入计算机。)
6. Restart your computer and enter the boot menu by
pressing the key or combination of keys displayed during
startup. This key varies depending on your computer's
manufacturer, but common keys include F12, Esc, or F8.
(重新启动计算机,并通过按下显示在启动过程中的键或键组合来
进入引导菜单。此键取决于计算机制造商,但常见的键包括F12、
Esc或F8。)
7. In the boot menu, select the appropriate option to boot
from the Windows 10 installation media that you inserted.
(在引导菜单中,选择适当的选项以从您插入的Windows 10安装介
质启动。)
8. Follow the on-screen instructions to begin the Windows
10 installation process. When prompted to choose an
installation type, select "Custom: Install Windows only
(advanced)".
(按照屏幕上的说明开始Windows 10安装过程。在提示选择安装类
型时,选择“自定义:仅安装Windows(高级)”。)
9. On the next screen, you will see a list of available
drives and partitions on your computer. Select the target
drive where you want to install Windows 10 and click "Next".
(在下一个屏幕上,您将看到计算机上可用驱动器和分区的列表。
选择要安装Windows 10的目标驱动器,然后点击“下一步”。)
10. The installation process will now begin. Follow the on-
screen instructions to complete the installation.
(现在,安装过程将开始。按照屏幕上的说明完成安装。)
11. Once the installation is finished, your computer will
restart. Remove the Windows 10 installation media from your
computer before it boots up again.
(安装完成后,计算机将重新启动。在计算机再次启动之前,请将
Windows 10安装介质从计算机中取出。)
12. Congratulations! You have successfully installed
Windows 10 in UEFI mode.
(恭喜!您已成功以UEFI模式安装了Windows 10。)
版权声明:本文标题:用uefi方式引导安装windows 10的方法 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://m.elefans.com/dianzi/1717425253a570645.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论