admin管理员组文章数量:1531469
2024年6月12日发(作者:)
TM
适合系统:维宏系统
Application system:Ncstudio
雕刻机无线遥控器
WHB02说明书
型号
MODEL:WHB02
The wireless Remote WHB02 manual
The product is Ncstudio system supporting the remote
control, can be applied only Ncstudio System Software
Support system: Ncstudio5X, Ncstudio8X
支持3轴位置调整
Supports 3-axis position adjustment
具有加工开始,停止,加工进给调节,主轴开启停止等功能
With the processing start, stop, and processing feed
adjusting spindle open stop functions
直视无障碍传输距离:60米
Barrier-free transmission distance: 60 meters
支持同一个房间,64套遥控器同时操作,相互不干扰
Support the same room, 64 sets of remote control
simultaneously, with no interference
采用低功耗设计,2节AAA电池,能使用6个月
The use of low-power design, 2 AAA batteries, can use six months
停止按钮
开始/暂停按钮
Stop button
Start / Pause button
断点继续按钮
Breakpoint Continue
回工件原点按钮
button
Back to the origin Button
直接设置为连续移动模式
直接设置步距为0.1
Continuous motion mode
Set step 0.1mm
直接设置步距为1
回机械原点按钮
Set step 1mm
Back mechanical
origin button
X轴正方向移动
Y轴正方向移动
X-axis positive direction
Y-axis positive direction
Z轴正方向移动
X轴负方向移动
Z-axis positive direction
X-axis negative direction
Y轴负方向移动
Y轴负方向移动
Y-axis negative direction
Y-axis negative direction
Z轴负方向移动
高速
Z-axis negative direction
High-speed mobile
微调按钮
主轴开启/停止
Fine adjustment
the spindle start or
stop button
X轴坐标清0,长按分中Y轴坐标清0,长按分中
Z轴坐标清0
步距调节增加
Step adjustment to
increase
步距调节减少
主轴转速增加
Step adjustment Reduce
Spindle speed increase
主轴转速减少
进给增加
Spindle speed Reduce
Increase in feed
-1-
进给减少
Reduced feed
固定对刀
Fixed height of the
calibration tool
Z安全高度设定
Z Coordinates 1/2 Button
浮动对刀开始/停止按钮
Floating on the knife start
or stop or reset Button
确认或取消当前操作:当NO和YES指示灯亮的时候,
按下NO,则取消当前操作;按下YES则确认当前操作
Confirm or cancel the current operation:When the NO and YES lights;
pressed NO,then cancel the current operation;Press YES to confirm
the current operation.
工作指示灯说明
Working Indicator Description
步距指示灯
Step LED
电池告警指示
Battery alarm LED
高速模式指示灯
High-speed mode LED
-2-
驱动安装升级说明
第一步:
(Step 1)
退出HB02驱动软件:如果你是第一次使用我们的软件,没有安装我们
的驱动,请跳过该步骤,直接执行第2步。
将鼠标放到电脑右下角的驱动图标上,点右键,退出我们的驱动软件。
step 1:
Exit HB02 driver software: If this is
your first time using our software,
our driver is not installed, skip this
step and go to step 2.
第二步:
(Step 2)
安装驱动:将光盘放入光驱,安装无线手柄的驱动,按照电脑提示,
直到安装成功,并结束安装。
step 2:Please send CD into the CD-ROM;Please follow the
computer prompts,Set up the Driver Software Until flished Set up。
中文版本驱动
Driver for English
-3-
驱动安装升级说明
注意:当使用英文版本的维宏系统,请安装英文版本的驱动;使用
中文版本的系统,请安装中文版本的驱动;否则 工作不正常。
Note:
When using the English version of the system, the installation
of the English version of the driver; using the Chinese version
of the system, install the driver of the Chinese version of the
work; otherwise abnormal.
,开始安装驱动鼠标双击图标
按照安装提示,直到驱动安装完成.
Please follow the computer prompts, Set up the Driver
Software Until flished Set up.
-4-
驱动安装升级说明
第三步:
(Step 3)
打开软件:打开刚刚安装的驱动软件,然后再打开数控系统软件NcStudio
step 3:
OPEN The Driver Software,then Open The NcStudio Software
从开始菜单里边打开刚刚安装的驱动
运行驱动后,出现驱动图标
Run the driver,the driver icon
-5-
驱动安装升级说明
第四步:
(Step 4)
将无线USB接收器,插入电脑的USB接口。如果是第1次使用,电
脑会提示找到新硬件设备......
等待USB驱动自动加载成功,插入USB接收器后,图标显示如下:
step 4:
Please Insert Wireless USB Receiver into USB Jack
If this is the 1st use, the computer will be prompted to find a new
hardware device;
Automatically install the USB driver to waitfor success.
USB receiver is inserted, the icon is displayed as follows:
图标变灰插入接收器后,
Receiver is inserted, the icon is
grayed out
第五步:
(Step 5)
启动维宏系统软件,图标变成红色。
step 5:Start Ncstudio system software, the icon turns red.
启动维宏系统软件,图标变成红色
Start Ncstudiosystem software,
第六步:
(Step 6)
the icon turns red
将无线手柄安装上2节AAA电池,注意电池的正负方向,不能装错。
手柄开始正常工作。
step 6:Installing 2 AAA Batteries into Remote; started to work.
-6-
TM
9
版权声明:本文标题:维宏系统无线手柄 WHB02 说明书 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://m.elefans.com/dianzi/1718150241a648839.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论