admin管理员组文章数量:1535343
2024年6月25日发(作者:)
迪士尼蓝牙耳机p1说明书
TWS-P1 (A)使用说明书
产品示意图
佩戴示意图
选择大小合适的耳套
我们提供了大中小三种规格耳套(图 a),请尝试并选择适合自己的尺寸以便获得最佳
的使用体验, 打开收纳盒拿出耳
机选择合适自己的耳套套上使其更舒适贴耳。
佩戴说明
耳机上有“L”及“R”标识,请将标有“L”的耳机戴在左耳,标有“R”的耳机戴
在右耳。
提示:您的左右耳可能适合不同尺寸的耳塞,将已装好耳塞的耳机塞进您的耳道,然
后转动耳机,定位至牢固舒服
的位置(如图 b)
(图 a) (图 b)
功能操作
首次使用说明
开机首次使用(或长时间不使用)时,使用前,请务必给耳机和充电座充电。
智能快捷连接
分别将左/右耳机从充电盒内拿出,左/右耳机会自动开机互联。连接成功后主机(左
耳机)将“蓝白灯”交替闪烁,
同时耳机会有语音提示“已连接,左声道,进入配对模式”,副机指示灯会进入白灯
慢闪,同时耳机会有语音提示
“已连接,右声道”。此时只需打开手机搜索蓝牙设备“P10”连接,即可正常使
用。当配对连接成功后耳机主机
(左声道)会有语音提示“配对成功,第二个装置连接成功”。
关机:
将耳机放入充电盒,耳机会自动关机并充电,若未带充电盒,可将手机断开蓝牙连
接,约 5 分钟后耳机会自动关机。
指示灯说明:
A、白灯闪三次,开机; 蓝灯闪三次,关机。
B、灯灭,无连接。
C、蓝白交替闪烁,等待连接手机蓝牙。
D、白灯每隔 5 秒闪一下,已连接上手机。
Siri 语音:
Ios 系统用户连接上耳机之后触摸主耳机或副耳机 2 秒,听到语音提示“滴”一声
松手,可唤醒或关闭 siri (此功能
仅支持 ios 系统用户),呼出 siri 之后可语音操作。
再次使用耳机:
分别将左/右耳机从充电盒内拿出,左右耳机会自动配对连接,主耳机也会自动连接
蓝牙(最后一次连接的设备)。
单耳使用:
当单个耳机使用时,只需拿出一个耳机,耳机拿出后会立刻闪白灯,然后触摸两下,
指示灯就会转成蓝白闪,耳机
进入蓝牙连接状态,打开手机搜索蓝牙设备名“P10”进行连接即可。左右耳机都有
独立通话功能。
提示:1)在主耳机(左耳)处于单耳连接模式下,如果想进行双耳 TWS 模式,只
需要将副耳机(右耳)从充电盒
中拿起,副耳机会自动和主耳机进行 TWS 配对连接。
2)在副耳机(右耳)处于单耳连接模式下,如果想进行双耳 TWS 模式,需将主耳
机(左耳)从充电盒中拿
起,触摸耳机表面 3 秒后松手,耳机进入开机模式,然后副耳机(右耳机)会自动
和主耳机(左耳机)进行 TWS
配对连接。
连接成功后主耳机会有语音提示“第二个装置配对成功,左声道”,副耳机语音提示
“右声道”。
功能操作:
来电提示/语音报号:在来电未接听电话时,两只耳机都会有提示音。
接听电话:来电时,触摸一下主耳机或副耳机。(通话时主耳机和副耳机都可以听到
对方声音)
挂断电话:通话中,触摸一下主耳机或副耳机。
拒接来电:来电时,触摸主耳机或副耳机 2 秒释放。
音乐播放:播放音乐时,触摸两下主耳机(左耳)切换上一曲;触摸两下副耳机(右
耳)切换下一曲。
播放音乐时,触摸一下主耳机或副耳机可暂停或播放音乐。
音量调节: 长按主耳机(左耳)3 秒以上, 可使音量渐渐减小(-); 长按副耳机(右耳)3 秒
以上, 可使音量渐渐加大(+)。
( 提示:请合理控制使用耳机的音量和时间;如果把音量调到太大,长时间听歌可能
会导致听力受损)
恢复出厂设置:(左右耳配对)
如果误操作耳机,造成两只耳机没有配对或是无法连接手机蓝牙,可以按下面方法让
左右耳机重新配对。
在充电的情况下,双手将(左/右)耳机“触摸区”,同时触摸 3 下直到左右耳机
“蓝灯”闪烁两次后,再从充电
盒中将左右耳机同时拿出,同时触摸左右耳机 5 秒直到蓝白灯交替闪烁,此时左右
耳机自动连接,连接成功后,主
耳机(左耳机)会自动进入配对状态,然后打开手机蓝牙就可以跟主耳机连接了。
耳机充电
1.将左右耳机放入充电盒内,开启充电盒电源,盖上盖子数秒后耳机便亮灯进入充电
状态。
2.充电状态时,耳机指示灯蓝灯慢闪。
3.充电完成,耳机满电后蓝灯会自动熄灭,30 秒后充电盒自动断电。
充电盒充电
1. 请使用输出电压为 DC5V/1A 的充电器对充电座充电,可使用电脑 USB 接口或
其他 USB 接口的充电器给充电盒充
电(必须选择正规厂家认证过的充电器)。
2. 充电盒充电期间,充电座有三个蓝色 LED 灯显示电量,蓝色 LED 灯会根据不同
的电量,闪烁不同电量的蓝色 LED
灯。(如:充电时第一个蓝灯闪烁,表示有 0-30%的电量;第一个蓝灯长亮,第二个
蓝灯闪烁,表示有 30-60%的电
量;两个蓝灯长亮,第三个蓝灯闪烁,表示有 60-99%的电量。)当充电座充满电时
三个蓝色 LED 灯会长亮,这时,
请将充电盒与充电设备断开连接。
注:充电器请使用 DC5V/1A 充电器或 PC 电脑的 USB;重复对耳机进行充电和放
电将会随时间的推移而导致电池效
能下降,这对所有可再充电电池来说都是正常的。(切勿用力挤压弹针触点以免导致
不能正常使用)
移动电源功能
将充电线直接接入数据线(安卓或苹果)插口,再连接充电盒上 USB 接口,开启充
电盒电源,就可以为手机充电。
(提示:需要给手机应急充电时,请先看看充电盒指示灯,只有 3 个蓝灯都亮时才
可以给手机充电,否则给手机充
电时无法达到效果。)
基本参数:
蓝牙版本 V5.0
支持协议 A2DP/AVRCP/HFP/HSP
传输距离 10M
频率范围 2402MHz~2480MHz
喇叭 Ф6MM*2 Hi-Fi Speaker
阻抗 16Ω
电压 3.7V
待机时间 70H
通话时间 3-5 小时
音乐播放时间 2.5 小时
耳机电池容量 45MAH
耳机充电时长 ≤2 小时
充电盒电池容量 3500MAH
充电盒充电时长 约 2.5 小时
支持系统 IOS/Android/Windows
认证 CE/FCC/ROHS
注意事项
1.请勿以任何理由拆除或改装耳机,否则可能导致耳机故障及烧毁,这些都不在保修
范围。
2.请勿将设备接触腐蚀性液体,否则会造成设备的严重损坏,由此造成的损坏,制造
商将不予以保修。
3.请勿将设备置于温度过高或过低(0 度以下或 45 度以上)的环境下。
4.请避免靠近儿童或动物的眼睛使用设备灯。
5.请勿在雷暴天气下使用设备,雷暴可能导致设备工作不正常,并增加触电的危险。
警告!
此产品含内置锂电池,请勿将此产品暴露在强烈的日照下,火烤或扔入火中,以免爆
炸。
常见问题
Q:充电盒充不进电?
A: 可更换一条数据线尝试一下,或接口没有接好。
Q: 耳机信号不稳定或耳机没声音?
A:请按上述佩戴方式佩戴好耳机,户外使用时请将手机放置在前口袋。
Q:搜索蓝牙出现两个“P10”设备名?
A:需将两个设备名删掉,再按(蓝牙配对)操作即可。
Q:接电话声音小或不清晰?
A:尽量把耳机音量调大或是将手机音量调大,并且手机不要离耳机太远。
Q: 如何单个耳机连接两部手机?
A: 先连接第一部手机蓝牙后, 再将其关闭蓝牙, 然后再连接第二部手机, 最后再将第
一部手机蓝牙开启后再手动连
接, 即可实现一拖二功能.
Q: 左耳跟右耳之间的传输距离有多远?
A: 正常无障碍的情况下为 3 米以内.
为了获得更好的音乐体验,建议使用 IOS8.0 & Android4.3 以上操作系统
TWS-P10 (A) Instruction Manual
Product Indication
Wearing sketches
Choose the suitable ear-pad from three sizes (small, medium, large) to make
you more comfortable.
Wearing instructions
Please wear the earphone marked "L" on the left ear and the one marked "R"
on the right ear.
Tip: Insert earphones with your ear-pads into your ear canal, then turn the
earphones to a firm and comfortable position.
(see figure b)
Functional operation
First use instructions:
When using it for the first time (or not using it for a long time), please make
sure to charge the earphones and charging
box before use.
Get quick started:
1) Take the L/R earphones out from the charging box and the L/R earphones
will power on and connect to each other
automatically.
2) After successful connection, the blue & white light of the master earphone
(left earphone) will blink alternately and it
voices “connected, left channel, pairing” as well. While the right earphone
will be white light blinking slowly and it voices
“connected, right channel”.
3) Turn on the mobile phone search bluetooth device “P10”, then click
connect and it voices “ second device connected” in
the master earphone (left earphone).
P10
Power off:
There are two ways to power off the earphones --
1) Put the earphones into the charging box , they will power off automatically
and enter into charging mode.
2) Disconnect the bluetooth connection between your mobile phone and the
earphones, the earphones will power off
automatically after about 5 minutes.
Indicator light status:
A. White indicator flashes three times-Power on;Blue indicator flashes three
times-Power off.
B. Indicator light off - Not connected.
C. Blue and White indicator flashes alternately- Two earphones connected
and waiting connection with mobile phone.
D. White indicator flashes slowly every 5 seconds- Connected with mobile
phone.
IOS/siri Active:
long touch the either of earphone for 2 seconds to activate Siri, Siri will be
ready to take commands after a sound “Siri”
played through. (This function is only supported for IOS system devices).
Use earphones again:
Take the L/R earphones out of the charging box and the L/R earphones will
power on and connect to each other
automatically. Then they will connect the bluetooth device automatically. (The
last connected bluetooth device.)
Use a single earphone:
Only take out any one earphone, the White light of this one will flash soon.
Then double click it, the indicator is changed to
blue & white light flickering. While turn on the cellphone, search the
bluetooth “P10” and connect. Left and right earphone
can be used separately.
Tips: 1) If the master earphone (left earphone) is being used as single
earphone and want to change TWS mode, you only
need to pick up the other earphone from the charging box. These two
earphone will connect each other automatically.
2) If the slave earphone(right earphone) is being used as single earphone and
want to change TWS mode, you need pick up
the other earphone, touch it for 3 seconds and then release. This earphone
will power on and will automatically connect
with the master (left earphone).
After the connection is successful, the master earphone will have the voice
prompt “second device connected, left
channel” and the slave earphone voice prompt “right channel”.
Functional operation:
Phone ring tone and sound can be heard from Both earphones.
Answer the phone: when calls come in, single-click either of earphones.
(Sounds can be heard from both earphones.)
Hang up the phone: during the call, single-click either of earphones.
Reject a call: when calls come in, long touch the either of earphones for 2
seconds.
Music play: In playing music, double-click the master earphone (left
earphone) for previous track; double-click the slave
earphone (right earphone) for next track; single-click the either of earphones
for pause or play music.
Decrease the volume(-): Long touch the master earphone (left earphone)
over 3 seconds to turn the
volume down.
Increase the volume(+): Long touch the slave earphone (right earphone) over
3 seconds to turn the volume
up.
(Tips:Please make reasonable volume and time, it will damage your
hearing if it is continuous long time
and high volume.)
Reset: (right / left earphones pair)
If two earphones cannot be connected each other or they cannot connect to
the mobile phone bluetooth due to
mis-operation, you can reset the earphones as the following method.
Put the earphones into the charging box and enter into the charging mode,
triple-click the earphone touch control at the
same time, until the blue lights flash twice. (You can do this one by one. )
Then take the both earphones out of the
charging box and long touch the earphones for 5 seconds at the same time,
until the earphones “Blue and white light”
flashes alternative then release. They will enter into paring mode
automatically. After successfully connection, turn on the
mobile phone bluetooth and connect.
Earphone charging:
1. Put two earphones into the charging box, cover the lid and the they will
enter into charging mode after several seconds.
2. blue indicators will flash slowly in charging mode.
3. Charging is completed: after the earphones are full power, the blue light
will go out automatically, and the charging box
will automatically cut off after 30 seconds.
Charging box battery charging
1. Please power the charging case by DC5V/1A adapter, PC USB port of PC or
other DC5V is OK.
2. In the charging mode, three blue LED indicator lights on the case show the
battery capacity.
Battery capacity indicator
A. One blue indicator flashes is 0%-30%
B. One indicator stays blue and one blue indicator flashes is 30%-60%
C. Three indicators stay blue is 60%-100%.
Please disconnect charging devices from the charging case once fully
charged.
Note: please charge for the case with DC5V/1A charger or Computer USB; As
the charging and discharging of the
earphones increases, the battery performance will decrease, which is normal
for all rechargeable batteries. (Don’t press
the contact of the spring pin hard to avoid improper use.)
Power bank function:
The charging box can be as power bank for your mobile phone. Charge your
Android or IOS device by connecting the Micro
USB cable to the charge port of your device and the standard USB connector
of the charging box.
(Tips:Please check the indicator of the charging box before charge to the
mobile phone. When all 3 indicators are lighting,
the charging box can be better charged for the mobile phone. )
Specification:
Bluetooth version V5.0
Support profile A2DP/AVRCP/HFP/HSP
Transmission distance 10M
Frequency range 2402MHz~2480MHz
Driver Ф6MM*2 Hi-Fi Speaker
Impedance 16Ω
Voltage 3.7V
Standby time 70H
Talking time 3-5H
Playing time 2.5H
Earphone battery 45MAH
Earphone charging time ≤2H
Charging box battery 3500MAH
Charging box charging time About 2.5H
Support system IOS/Android/Windows
Certification CE/FCC/ROHS
Attention:
1. Do not remove or refit earphones for any reason, otherwise it will lead to
headset damaged and burn. These are not
covered by warranty.
2. Do not touch the earphones in corrosive liquid, otherwise it will cause
serious damage. The manufacturer will not
guarantee the damage caused under this situation.
3. Do not put the equipment under too high or too low temperature( Below
0°C or above 40°C).
4. Please avoid approaching the eyes of children or animals when using
equipment lights.
5. Do not use equipment in the thunderstorm weather. Thunderstorms may
cause abnormal equipment operation and
increase the risk of electric shock.
Warning:
This product contains a built-in lithium battery. Please do not expose this
product to strong sunlight, roasting or throwing it
into the fire, as they may explode
FAQ
Q: Charging case can not charge?
A: Ensure that the charging cable is properly connected to the charging port
or replace charging cable。
Q: Signal is not stable or left earphone is out of voice?
A: Try to wear the earphones well, and put the mobile on front pocket when
used in outdoor.
Q: When search the bluetooth, display two connection names of “P10”?
A: Forget the two bluetooth name of “P10”, turn off the bluetooth and
connect as above “get quick start”.
Q: The sound volume is down or not clear when making calls?
A: Try to turn the earphone volume up or turn the mobile phone volume up,
and move phone closer to the earphones.
Q: How to connect two cellphones to an earphone?
A: Connect your first mobile phone to bluetooth and then turn off bluetooth ,
then connect second mobile phone. Finally,
turn on the first mobile phone bluetooth and connect it again.
Q: How far is the distance between the left earphone and the right one?
A: 3M in the normal environment without barrier.
For better sound quality experience, suggest use IOS 8.0/ Android 4.3 or
above operation system.
NOTE: This equipment has been tested and found to comply with the limits
for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions,
may cause harmful interference to radio communications. However, there is
no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which
can be determined by turning the equipment off and on, the user is
encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible
for compliance
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may
cause undesired operation.
版权声明:本文标题:迪士尼蓝牙耳机p1说明书 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://m.elefans.com/dianzi/1719289378a768971.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论