admin管理员组文章数量:1534625
2024年3月22日发(作者:)
第一部分:TiNetS2000EI系列配置命令及说明
(红色标识为一些常用命令)
Username(1-32chars):admin
Password(1-16chars):******/登陆交换机,默认密码123456/
TiNet>enable/进入特权模式/
TiNet#configureterminal/进入全局模式/
TiNet(config)#
1. TINET#terminallanguage/改变语言模式/
例如:TINET#terminallanguageChinese/改成中文模式/
#clearstartup-config/清除配置,恢复出厂默设置/
3. TiNet#copyrunning-configstartup-config/保存配置命令/
4. TiNet#load?
application下载应用程序
configuration下载配置文件
keyfile下载SSH密钥文件
whole-bootrom下载全部的bootrom/设备升级命令/
5. TiNet(config)#ipaddress192.168.
/配置交换机IP地址/
6. TiNet(config)show?/show命令,后可以打问号/
Showip
Showmac
Showinterface
Showvlan
7. TiNet(config)#vlan3901/建立VLAN3901/
TiNet(config-if-vlan)#switchportethernet0/1/把端口1加入该VLAN/
TiNet(config)#ipvlan3901/定义管理vlan为3901
TiNet(config)#noipvlan1/删除默认管理VLAN1/
8. TiNet(config)#vlan1001-1512/批量建立VLAN/
9. TiNet(config-if-vlan)#switchportethernet0/2toethernet0/8ethernet0/11ethernet0/16
/在某一VLAN中或者VLAN段中批量加入端口/
10. TiNet(config-if-ethernet-0/16)#tagvlan1001,1112-1512,4000
/端口下批量打tag/
11. TiNet(config-if-ethernet-0/1)#switchportmodetrunk
/改变端口模式,为trunk模式/
12. TiNet(config-if-ethernet-0/1)#switchporttrunkallowedvlanall
/端口为trunk模式,允许所有VLAN通过/
13. TiNet(config-if-ethernet-0/2)#switchportaccessvlan1001
/改变端口PVID/
14. TiNet(config)#port-isolationethernet?
STRING<3-4>端口号为槽端口号<0-2>/端口号<1-24>
TiNet(config)#port-isolationethernet0/2toe0/16
添加端口隔离下行端口成功./一步隔离,一条命令隔离除上行口以外所有端口/
15. TiNet(config)#interfacerangeethernet0/2toethernet0/16/批量端口处理命令/
16. TiNet(config-if-range)#bandwidth-control?
egress出口带宽控制
ingress入口带宽控制/端口限速命令/
17. TiNet(config)#showutilizationinterface/实时查看端口流量占比/
LinkUtilizationAveragesThuJan100:43:201970
portlinkReceivePeakRxTransmitPeakTx
Statuspkts/secpkts/secpkts/secpkts/sec
==================================================================
e0/1down0000
e0/2down0000
e0/3down0000
e0/4down0000
e0/5down0000
e0/6down0000
e0/7down0000
e0/8down0000
e0/9down0000
e0/10down0000
e0/11down0000
e0/12down0000
e0/13down0000
e0/14down0000
e0/15down0000
e0/16down0000
e1/1down0000
====spacebar->togglescreenU->pageupD->pagedownCR->exit====
通过空格键来切换回车键结束查看
18. TiNet(config)#usernamechange-passwo请输入您的登录密码:******
请输入用户名(4--15位):admin
请输入新口令(1--15位):********
输入确认口令(1--15位):********
用户admin密码修改成功。/修改登陆密码/
配置案例:
小河区某小区格林耐特设备配置
简要流程
/配置ip地址/
ConfigIPsuccessfully.
TiNet(config)#showip
Switchconfiguration
ipobtained:MANUAL
netmask:
ManageVLAN:1
MACaddress:00:0a:5a:11:ba:b8/查看交换机ip地址/
TiNet(config)#ex
TiNet#terminallanguagechinese/更改语言模式为中文/
TiNet(config)#vlan3901/建立vlan3901/
TiNet(config-if-vlan)#switchportall/在vlan3901下添加端口/
添加VLAN端口成功!
TiNet(config)#ipaddressvlan3901/定义交换机管理vlan/
配置管理VLAN成功!
TiNet(config)#showip
交换机的配置信息
IP地址获得方式:MANUAL
管理VLAN:13901/此时管理vlan为1和3901/
MAC地址:00:0a:5a:11:ba:b8
TiNet(config)#noipaddressvlan1/删除交换机默认管理vlan1/
删除管理VLAN成功!
TiNet(config)#showip
交换机的配置信息
IP地址获得方式:MANUAL
管理VLAN:3901
MAC地址:00:0a:5a:11:ba:b8/管理vlan已改为3901/
TiNet(config)#interrangeethernet0/1toethernet0/16/批量进入端口1-16
TiNet(config-if-range)#tagvlan3901/端口1-16tagvlan3901/
TiNet(config-if-range)#ex
TiNet(config)#vlan1001/建立vlan1001/
TiNet(config-if-vlan)#switchportethernet0/1/vlan1001中加入端口1/
添加VLAN端口成功!
TiNet(config-if-vlan)#showvlan1001
显示VLAN信息
VLANID:1001
VLANstatus:static
VLANmember:e0/1.
Statictaggedports:
StaticuntaggedPorts:e0/1.
Dynamictaggedports:
TiNet(config)#vlan1015-1030/批量建立vlan1015-1030/
TiNet(config-if-vlan)#switchportethernet0/1ethernet0/16
/vlan1015-1030加入端口1-16/
添加VLAN端口成功!
TiNet(config-if-vlan)#showvlan1015
显示VLAN信息
VLANID:1015
VLANstatus:static
VLANmember:e0/1,e0/16.
Statictaggedports:
StaticuntaggedPorts:e0/1,e0/16.
Dynamictaggedports:
TiNet(config)#port-isolationethernet0/2toe0/16/端口2-16进行隔离,1口为上行口,未隔离
/
添加端口隔离下行端口成功.
TiNet(config-if-ethernet-0/1)#switchport?
accessaccess端口
backup配置备份端口
mode端口模式
trunktrunk端口
TiNet(config-if-ethernet-0/1)#switchportmodetrunk
/更改端口1模式为trunk/
TiNet(config-if-ethernet-0/1)#switchporttrunkallowedvlanall
/允许所有vlan通过1口/
TiNet(config-if-ethernet-0/1)#switchporttrunknativevlan3901
/更改1口pvid为3901/
TiNet(config-if-ethernet-0/1)#ex
TiNet(config)#showutilizationinterface/查看端口实时流量/
LinkUtilizationAveragesThuJan100:24:371970
portlinkReceivePeakRxTransmitPeakTx
Statuspkts/secpkts/secpkts/secpkts/sec
==================================================================
e0/1down0000
e0/2down0000
e0/3down0000
e0/4down0000
e0/5down0000
e0/6down0000
e0/7down0000
e0/8down0000
e0/9down0000
e0/10down0000
e0/11down0000
e0/12down0000
e0/13down0000
e0/14down0000
e0/15down0000
e0/16down0000
e1/1down0000
====spacebar->togglescreenU->pageupD->pagedownCR->exit====
TiNet(config)#usernamechange-password/修改登录密码/
请输入您的登录密码:******
请输入用户名(4--15位):admin
请输入新口令(1--15位):******
输入确认口令(1--15位):******
/用户admin密码修改成功/
TiNet#copyrunning-configstartup-config/保存配置命令/
第二部分:交换机实现telnet管理配置步骤
第一步:配置规划好的交换机ip地址
例:
/配置ip地址/
ConfigIPsuccessfully.
TiNet(config)#showip
Switchconfiguration
ipobtained:MANUAL
ManageVLAN:1
MACaddress:00:0a:5a:11:ba:b8/查看交换机ip地址/
第二步:建立规划好的管理vlan,把上行口加入到管理vlan中,然后删除默认的管理vlan1
例:
TiNet(config)#vlan3901/建立vlan3901/
TiNet(config-if-vlan)#switchporte0/1/在vlan3901中添加端口1/
添加VLAN端口成功!
TiNet(config)#ipaddressvlan3901/定义交换机管理vlan/
配置管理VLAN成功!
TiNet(config)#showip
交换机的配置信息
IP地址获得方式:MANUAL
管理VLAN:13901/此时管理vlan为1和3901/
MAC地址:00:0a:5a:11:ba:b8
TiNet(config)#noipaddressvlan1/删除交换机默认管理vlan1/
删除管理VLAN成功!
第三步:进入上行口,给管理vlan打标
例:
TiNet(config)#interfaceethernet0/1/进入到上行口模式/
TiNet(config-if-ethernet-0/1)#tagvlan3901/打标/
经过以上三个步骤,如果上层级联交换机配置无误,就可以远程telnet管理交换机。
第三部分:交换机SNMP网管配置
TiNet(config)#snmp-servercommunitygzgy@))*rwpermit
2cgzgy@))*
2cgzgy@))*
2cgzgy@))*
交换机默认开启SNMP代理功能和默认支持SNMPv1/v2/v3,无需其他配置,。
汇聚交换机与楼层交换机同样配置。
版权声明:本文标题:新格林耐特配置命令 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://m.elefans.com/dongtai/1711113082a300346.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论