admin管理员组文章数量:1539834
2024年4月28日发(作者：)
IQ 安装步骤
1. Boot the system from the Software Tape.
2. Select option 3 "Restore Both" from the ELTP.
3. Select "Start Xfer". Transfer takes about 5 minutes.
4. Touch "Continue" when prompted.
5. Remove the tape from the tape drive.
6. Select option 5 "Boot OS".
7. Select option 1 "From Disk".
8. 'Software Configuration' is automatically done. No menu is displayed.
9. When prompted to restore site information, respond with t,f or n.
10. When prompted to install diagnostics, respond with t, f or n.
11. Select P (for PQ), I (for IQ) or C (for CUSTOMER) diagnostics.
Remove the diagnostics tape when done.
12. When prompted to install camera software, respond with t, f or n.
Remove the camera software tape when do
CAUTION
Perform the following step only if all images have been archived. Otherwise
answer Y to the question "REBUILD IMAGE DIRECTORIES?"
13. When asked if to initialize the image partitions, answer 'y' (y,y,a).
14. At the 'Startup' menu, select 3 "Hard Disk File System Check"
15. At the 'Startup' menu, select 1 "Scanner Startup".
16. Check the study number.
17. Run 'addlog' and make an entry in the that software was
loaded.
18. Run 'print_cnf' and verify the system has the correct options.
19. Exercise the system via warmup, pilots and scanning.
20. Retrieve Images from tape and display to verify proper operation.
21. Verify camera filming operation in both square and rectangular formats.
22. Run 'save_site' and properly label the tape.
23. Run 'pity' from 'cddiag' and label the tape.
RESTORING SYSTEM SOFTWARE FROM TAPE (pity)
1. Boot the system from a bootable tape created with the 'pity' utility.
2. Select option 3 "Restore Both" from the menu.
3. Select "Start Transfer". Transfer takes about 5 minutes.
4. Touch "Continue" when prompted.
5. Remove the tape from the tape drive.
6. Select option 5 "Boot OS".
7. Select option 1 "From Disk".
8. Answer 'n' when asked to load the Site, Diagnostic, and Camera tapes.
9. When asked if to initialize the image partitions, answer 'y' (y,y,a).
10. At the 'Startup' menu, select 3 "Hard Disk File System Check"
11. At the 'Startup' menu, select 1 "Scanner Startup".
if you answer yes to th following questing,all inmages that might exist on the
image partions will be lost
initialize the image partinos?
are you sure you want to destroy all data on the image partintions
rebuild database directory
scanner stratup
preapare system for powerdown
hard disk file system check
rebuild image directory
reguius user mode
delete all images
RDT daemon 0 starts
performing forward file
target device main disc
selection status=-2
scsi device tape
T.O. during scsi bommed
scsi bus lock-up detected
scsi reset has been issued
system monitor board did not accept
the cmnd AFF
cmnd AFF
版权声明：本文标题：IQ 安装步骤 内容由热心网友自发贡献，该文观点仅代表作者本人， 转载请联系作者并注明出处：https://m.elefans.com/dongtai/1714285109a396749.html， 本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容，一经查实，本站将立刻删除。
发表评论