戴尔Alienware Aurora R6 R7 U.2固态硬盘安装指南说明书

2024-07-27 作者:

Aurora R6/R7

U.2 Solid-State Drive

Installation Guide

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION:

A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the G: A WARNING indicates a potential for property damage, personal injury, or death.

© 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

2018 - 08Rev. A00

1 Before working inside 4

Before you begin ...............................................................................................................................................................52 Installing the U.2 .63 After working inside 154 Getting help and 16

16

Contents3

1

Before working inside your computer

NOTE: The images in this document may differ from your computer depending on the configuration you :•••

Before you begin

Safety instructionsRecommended tools

Before you begin

1 2

Save and close all open files and exit all open down your computer.

Windows 10: Click or tap Start

> Power > Shut down.

NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down instructions.

3

4

5

6 7

Disconnect your computer and all attached devices from their electrical outlets.

Disconnect all cables such as telephone cables, network cables, and so on, from your computer.

Disconnect all attached devices and peripherals, such as keyboard, mouse, monitor, and so on, from your any media card and optical disc from your computer, if applicable.

After the computer is unplugged, press and hold the power button for 5 seconds to ground the system board.

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and ensure your personal safety.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For more safety

best practices, see the Regulatory Compliance home page at /regulatory_compliance.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the

computer, replace all covers, panels, and screws before connecting to the electrical N: To avoid damaging the computer, ensure that the work surface is flat and clean.

CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching pins and N: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team.

Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that shipped

with the product or at /regulatory_compliance.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the

metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.

CAUTION: When you disconnect a cable, pull on its connector or on its pull tab, not on the cable itself. Some cables have

connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When disconnecting

cables, keep them evenly aligned to avoid bending any connector pins. When connecting cables, ensure that the ports and connectors are correctly oriented and aligned.

4Before working inside your computer

Before working inside your computer5

CAUTION: Press and eject any installed card from the media-card reader.

Recommended tools

The procedures in this document may require the following tools:•••

Philips screwdriver #1Flat-head screwdriverPlastic scribe

2

Installing the U.2 solid-state drive

NOTE:

Ensure that you remove the security cable and security screw from the security-cable slot—if applicable.1

2 3

Remove the screw (#6-32 X 1/2") that secures the side-panel release latch to the the side-panel release latch.

Release the left-side cover away from the chassis and then lift it from the computer.

Figure 1. Removing the left-side cover

13

4

5 6

screwtop cover

24

side-panel release latchleft-side cover

Lay the computer on the right side.

Disconnect the data and power cables from the hard drive.

Press the release tabs on the hard-drive carrier and slide the hard-drive carrier out of the hard-drive cage.

6Installing the U.2 solid-state drive

Figure 2. Removing the hard drive

1data cable2power cable3hard-drive cage4

release tabs

5

hard-drive carrier

7

Place the U.2 solid-state drive in the hard-drive carrier and align the tabs on the carrier with the slots on the U.2 solid-state drive.

Figure 3. Assembling the U.2 solid-state drive

1

hard-drive carrier

2

fan cable

Installing the U.2 solid-state drive7

3

8

U.2 solid-state drive

Slide the U.2 solid-state drive assembly into the hard-drive cage until it snaps into place.

Figure 4. U.2 solid-state drive assembly

1

9

solid-state drive assembly

2

chassis

Slide the power-supply unit cage release latches towards the unlock position.

Figure 5. Sliding the power-supply unit cage release latches

13

power-supply unit

power-supply unit cage release cage latches (2)

2

chassis

10 Lift the power-supply unit cage while pressing and holding the graphics-card bracket.

8Installing the U.2 solid-state drive

Figure 6. Rotating the power-supply unit

1power-supply unit cage2

graphics-card bracket

3

chassis

11

Rotate the power-supply unit cage away from the chassis.

Installing the U.2 solid-state drive9

Figure 7. Rotating the power-supply unit

1

power-supply unit

12 Lift to release the graphics-card bracket from the chassis.

10Installing the U.2 solid-state drive

Figure 8. Removing the graphics card

1

graphics-card bracket

2

graphics card

13 Press the releasing clip on the power-cable connectors and disconnect the power cables from the graphics card.

14 Push the securing tab on the PCIe slot away from the graphics card, grasp the card by its top corner, and ease it out of the slot.

Installing the U.2 solid-state drive11

Figure 9. Removing the graphics card

13

power cablesgraphics card

24

releasing clips (2)securing tab

15 Slide the fan cable and the data and power cable through the power-supply unit cage.16 Connect the fan cable to the system board.17 Connect the power cable to the power-supply unit.

18 Connect the data cable to the connector on the solid-state drive adapter.

19 Slide the solid-state drive adapter to the solid-state drive slot and replace the screw that secures the solid-state drive adapter to the

system board.

12Installing the U.2 solid-state drive

Figure 10. Connecting the cables

1solid-state drive slot2screw

3data cable4solid-state drive adapter5

power cable

6

fan cable

20 Align the graphics card with the slot on the system board.

21 Place the graphics card into the slot and press down firmly until the graphics card snaps into place.22 Connect the power cables to the graphics card.

23 Slide the tab on the graphics-card bracket into the slot on the chassis and snap it into place.24 Rotate the power-supply unit cage towards the chassis until the unit snaps into place.25 Connect the power cable to the U.2 solid-state drive.

Installing the U.2 solid-state drive13

Figure 11. Connecting the power cable

1

chassis

2

power cable

26 Place the computer in an upright position.

27 Align the tabs on the left-side cover with the slots on the chassis.28 Snap the left-side cover to lock it in place.

Figure 12. Replacing the left-side cover

13

chassistabs

24

slots

left-side cover

29 Replace the screw (#6-32 X 1/2") that secures the side-panel release latch to the chassis.

14Installing the U.2 solid-state drive

3

After working inside your computer

CAUTION:

Leaving stray or loose screws inside your computer may severely damage your computer.1

2

3 Replace all screws and ensure that no stray screws remain inside your computer.

Connect any external devices, peripherals, or cables you removed before working on your e any media cards, discs, or any other parts that you removed before working on your computer.4 Connect your computer and all attached devices to their electrical outlets.5

Turn on your computer.

After working inside your computer15

4

Getting help and contacting Alienware

Self-help resources

You can get information and help on Alienware products and services using these online self-help resources:Table 1. Self-help resources

Information about Alienware products and services

Troubleshooting information, user manuals, setup instructions,

product specifications, technical help blogs, drivers, software updates, and so on

/gamingservices

Videos providing step-by-step instructions to service your /alienwareservices

Contacting Alienware

To contact Alienware for sales, technical support, or customer service issues, see .

NOTE: Availability varies by country and product, and some services may not be available in your country.

NOTE: If you do not have an active internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.

16Getting help and contacting Alienware