Flysky FS-A8S 接收机说明书

admin管理员组

文章数量:1530879

2024年7月24日发(作者：)

FS-A8S

FS-A8S是一款专用于穿越机的单向接收机，采用了AFHDS

2A（第二代增强版自动跳频数字系统）。它体积小巧便于

安装，可输出标准PPM信号和18个通道的i-BUS信号以

及16通道的信号。

接收机 Receiver

The FS-A8S is a compact 1-way receiver designed for Drone

aircraft. It uses the AFHDS 2A (Automatic Frequency Hopping

Digital System) protocol, supports standard PPM output and has

i-BUS support for up to 18 also has support for

up to 16 channels.

产品介绍

Introduction

接收机概览

Receiver overview

用于连接接收机与模型的各个部件。

PPM信号接口： 输出标准的PPM 信号；

i-BUS/信号接口: 用于输出i-BUS/信号。

These ports are for connecting the receiver to various models and

flight controllers.

PPM signal port: Outputs standard PPM signal.

i-BUS/ signal port: Outputs i-BUS/ signal.

注：接收机将 RSSI 数据转换成 CH14 通道值通过 i-BUS/ 输出给

飞控，信号强度为 0 时对应通道值为 1000，信号强度为 100 时对应通

道值为 2000，线性对应相关。

Note: The receiver uses CH14 for output of RSSI data to the

onboard flight controller via i-BUS/. The receiver signal

strength data from the onboard flight controller will be displayed

as values between 0 and 100 (100 being max signal strength) and

the corresponding values displayed on CH14 on the transmitter

will be 1000 and 2000 (2000 being max signal strength).

产品型号：FS-A8S

适用机型：穿越机

无线频率：2.4GHz

无线协议：AFHDS 2A

天线类型：单天线

输入电源：4.0～8.4V

数据输出：PPM/ i-BUS/

温度范围：

-15℃—+60℃

湿度范围：

20%-95%

在线更新：无

外形尺寸：20mm*14mm*5.3mm

机身重量：1.2g

安规认证：CE，FCC

产品规格

Product specification

Product Name: FS-A8S

Model Type : Multi-rotor

RF: 2.4GHz

Protocol: AFHDS 2A

Antenna: Single Antenna

Input Power: 4.0-8.4V

Data Output: PPM/i-BUS/

Temperature Range: -15℃—+60℃

Humidity Limit: 20%-95%

Online Update: no

Dimensions: 20mm*14mm*5.3mm

Weight: 1.2g

Certification: CE，FCC

1. 将发射机进入对码状态；（发射机进入对码状态的方式可能不同，请根据发射 机的使用说明书进行操作）

2. 按住接收机上的对码按键，并为接收机连接电源。接收机上的指示灯快闪表示接收机进入对码状态；对码成功后，接

收机状态指示灯由快速闪烁变为慢速闪烁。

3. 将发射机手动退出对码界面，此时接收机状态指示灯变为常亮。

4. 检查发射机、接收机、模型是否正常工作。如有异常，重复以上步骤重新对码。

1. For information on putting the transmitter into bind mode please refer to the transmitters user manual.

2. Power on the receiver while holding the bind button. If the receiver's LED is flashing this means it has entered bind

mode.

If binding is successful the receiver's LED will begin to flash slower.

3. On the transmitter, manually exit the binding menu. Once you have exited the bind menu the receiver's LED will stop

flashing and remain solid.

4. Check to make sure the model and receiver work as expected. If anything does not work as correctly, restart this

对码

Binding

Copyright ©2021Flysky Technology co., ltd

失控保护功能用于在接收机失去信号不受控制后，保护模

型及人员安全。

• 本款接收机失控保护值不支持用户设置，失控后通道

无输出。

失控保护

Failsafe

FS-A8S

接收机 Receiver

This function protects your vehicle by preventing unexpected

behaviors in case of signal lost.

• The failsafe value of this receiver does not support user

settings, and the channel will have no output after loss of

control.

注意事项：

• 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。

• 关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备

失控或者引擎继续工作而引发事故。

• 确保接收机安装在远离电机，电子调速器或电子噪声过多的区域。

• 接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有1厘

米以上的距离。

• 准备过程中，请勿连接接收机电源，避免造成不必要的损失。

Attention:

• Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.

• Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended

operation or loss of control.

• Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical

noise.

• Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.

• Do not power on the receiver during the setup process to prevent loss of control.

Copyright ©2021Flysky Technology co., ltd

FS-A8S

FCC Compliance Statement

接收机 Receiver

认证相关

Certification

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

DoC Declaration

CE Warning

Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FS-A8S] is in compliance with RED 2014/53/EU.

The full text of the EU DoC is available at the following internet address: .

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not

be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation

instructions and transmitter operating conditions for satisfying RF exposure compliance.

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at

the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these

collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the

treatment of toxic substances.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Copyright ©2021Flysky Technology co., ltd

本文标签： 接收机发射机模型失控电源