ekwb ek-fc1080gtx-ti-ace-install 安装手册说明书

admin管理员组

文章数量:1530842

2024年6月20日发(作者：)

Installation manual for EK-FB ASUS R4BE Monoblock water block

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Rampage IV Black Edition motherboard

IMPORTANT NOTICE:

ROG LED (Logo) has to be removed in order to

successfully complete installation of the FB KIT

ASUS R4BE and cannot be used in combination

with the FB KIT ASUS R4BE.

Mosfets

CPU socket

X79 PCH (SB)

STEP 1: PREPARING YOUR MOTHERBOARD

STEP 2: REMOVING THE ORIGINAL LATCH MECHANISM

BACKPLATE

Please remove your motherboard from the computer to assure safest

1. REMOVING STOCK COOLER.

Remove all encircled screws. There are 13 screws on the back of

Do not

remove the

X79 PCH (SB)

backplate!

the motherboard that needs to be removed in order to remove the factory installed SB/MOSFET heat

pipe cooling solution.

mounting process possible in order to prevent any possible damages to

your PCB. With the enclosed Torx T20 key please remove all four (4)

screws securing the socket latch mechanism (ILM) to original backplate

(BP) to the motherboard. Make sure you have install the plastic

cover over the socket pins and that the socket latches are in

OPEN position during this procedure!

Use plastic

socket cover

during install!

STEP 4: PREPARING YOUR MOTHERBOARD

After removing the original LGA-2011 backplate, installed on your ASUS Rampage IV Black Edition

2. CLEANING THE PCB.

Carefully detach the original stock cooler after

STEP 3: INSTALLING ALTERNATIVE LGA-2011 BACKPLATE

motherboard, it is mandatory to install the alternative LGA-2011 provided with your motherboard.

Use the enclosed Torx T20 key to re-install it. Make sure you have install the plastic cover

over the socket pins and that the socket latches are in OPEN position during this

procedure! It is now a prime time to install your LGA-2011 CPU into the motherboard socket.

removing all screws securing it to the board. Wipe off the remains (by

using non–abrasive cloth or

qtip

, as shown on sample photo) of the

original thermal compound until the components and circuit board are

completely clean. EKWB recommends the use of denatured alcohol for

removing TIM leftovers.

3. APPLYING THERMAL COMPOUND

. Apply thermal compound:

lightly coat the Intel X79 (PCH) – see sample photo on the left and

CPU heat spreader (IHS) - see sample photo on right

with

enclosed EK-TIM Ectotherm thermal grease.

The quantity of about two rice grains is just about right. There is no need to cover the

whole IHS. Applying too much thermal grease will have negative impact on the cooling

performance!

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on December 20

th

2013

4. CUTTING THERMAL PADS.

Your block comes with thermal pads which needs to be trimmed in order to fit the voltage

regulation area (VRM/MOSFET) on the motherboard’s circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE

SCALED.

1: Thermal pad A – 0.5mm

(for VRM/MOSFET):

Replacement thermal pads @ EKWB web shop:

Thermal PAD A 1mm - (100x16mm) [EAN: 383]

Thermal PAD A 0.5mm - (100x16mm) [EAN: 383]

2: Thermal pad A – 1.0mm

(for inductor coils):

5. PLACING THERMAL PADS ON MOTHERBOARD.

Place thermal pads you cut on PCB as shown on picture bellow (PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH

SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION). EK recommends using small drops of electrically non-conductive (for example: EK-Ectotherm, Gelid GC-Extreme,

Arctic Cooling MX-2 ™ or MX-4 ™) thermal grease on each phase regulator (that is being covered with thermal pad; see picture below) in order to even further improve the

thermal performance of the EK-FB ASUS RE4BE Monoblock series water block.

Place 0.5mm thermal pads in larger

strips over marked area and make sure

all mosfet chips are covered.

Place 1mm thermal pads in larger strips over

the coils (inductors). This is merely to prevent

any possible short circuiting. Due to the

uneven nature of motherboard manufacturing

not all of the inductors will have contact with

the thermal pad. This is normal.

STEP 5: PLACING THE BLOCK ON TO MOTHERBOARD STEP 6: ATTACHING BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

1. PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB ASUS M6I series

water block gently to the motherboard or vice versa (as shown on photo below). Make

motherboard’s circuit board are aligned with the water block.

sure that mounting holes are aligned.

A) SB part: Use five M3x4 DIN7985 and washers. Tighten the screws, beginning near

the south bridge, and continue evenly outwards. Do not use excessive force when

tightening the screws!

B) MOSFET part: Use ASUS factory (“stock”) backplate and two M3x8 DIN7985

screws. Do not use excessive force when tightening the screws!

C) CPU part: Use four M4x8 DIN7985 screws and washers. Tighten the screws using

enclosed Alley Key 2.5mm.

Use the enclosed screws and washers as shown in picture below:

M3x8 screw

ASUS factory Mosfet

backplate

M4x8 screw

M3x4 screw

PVC washer

ASUS factory PCH

backplate

8. POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

For the EK-FB ASUS R4BE Monoblock series water block to operate properly the G1/4 port nearest to the center of the water block MUST BE USED AS THE

INLET PORT. EK recommends the use of EK-CSQ fittings. When using fittings other than EK-CSQ series please use hose clamps or appropriate substitute to

secure the tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is always recommended for any liquid cooling system.

Tubing

IMPORTANT: USE THIS

OPENING AS AN INLET

PORT!

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on December 20

th

2013

本文标签： 说明书手册安装